Completely New Prolific Tool Holders Coming From Iscar Direct The Way In Machining Production

Iscar's Heliturn system features a unique, double-sided insert with 4 cutting edges for Fast Metal Removal (FMR) turning. The brand new Heliturn is a tangentially clamped insert having a specific helical shaped cutting edge, useful for immense depths of cut and higher than normal feed rate. The LNMX...-HT Heliturn insert is screw-clamped into the SLANR tool holder and held by the TLN ..-HT carbide seat. This seat has ground surfaces on the top and bottom, to insure perfect contact of the insert with the tool holders. The upper rake face of this insert is mounted level with the top of the tool holder to enable chips to flow across the insert, without being afflicted by clamps or the tool holder body. The 4 curved helical cutting edges provide positive radial rake angles and soft penetration into the metal being cut. The decreased forces and smaller loads assure better tool life, elevated stability and the ability to use extraordinarily large depths of cut and larger feeds. The chipformer, deforms and breaks the chip into rib type curved fragments which can successfully be removed from the cutting area. The insert has a frontal clearance angle of 3.7 with a 6 side clearance angle to allow machining to a 90 shoulder. Depths of cut up to .315" and facing depths to .126" at up to .047" IPR are attainable with Heliturn.

When assimilated to CNMG/M 16... or WNMG/M 13... insert sizes with the same corner radius, much greater tool life can be envisioned when using the LNMX 1506..-HT insert. Iscar has recently released a lesser size to the Heliturn family - the LNMX 1104..R/L-HT insert and tool holder for the medium application range of up to .197" depth of cut. The brand new insert features all of the advantages of the larger insert. This enhances the economical usefulness in the medium machining application range. When compared to CNMG/M 43. 12... or WNMG/M 43. 08... insert sizes with the same corner radius, a significantly better tool life can be expected. The inserts are offered in .031, .047 and .063" tool nose radii. Heliturn inserts are attainable in the most superior carbide grades: IC9025, IC3028 , IC428, IC907, and IC908.

The external tool holders are presented in 1, 1.25 and 1.5" shank sizes. Boring bars are available in 1, 1.25 1.5 and 2" bar sizes. Also obtainable are exchangeable heads. These tool holders have Iscar's unique Hard Touch coating, which enhances/increases/expands/heightens/stretches holder life and resists corrosion. As a result of the positioning of this insert, machining next to the tailstock is permissible.

The high positive rake angle of these cutters allows 10-15% less power consumption/utilization/expenditure than traditional tool holders at the same parameters.

By using Iscar's Heliturn tools, huge cost savings and profitability in lathe procedures is insured.

A New 80 Degree Rhombic Insert with high helical cutting edge for high metal removal rates Iscar is announcing the CNMX 1207..-HTW insert family. The brand new insert has a very positive radial, helical cutting edge and a positive rake angle; a blending which extensively reduces the cutting forces. The insert's corner has a wiper configuration which produces high surface finish even at high feed conditions, which in abundant occasions can relinquish a finishing cut. The corner angle is 88 degrees which provides increased strength. The CNMX inserts were built for heavy machining applications. Their distinctive design ensures reputable, fast metal removal when using 80 degree rhombic inserts. They can be mounted on any conventional tool holder that carries regular CNMG inserts, but the seat has to be replaced with a special seat: TCH 4. Iscar's R-clamp tool holders are highly recommended for heavy machining applications.

Easy Methods To Buy A Megger Tester
A Megger tester is a device that is commonly used in electrical contracting to determine if the system has been properly installed.

A Wood Chipper Can Make It A Lot Easier To Clear Away Twigs In Your Lawn
A wood chipper can be a great tool to help clean up your yard and for making chips for landscaping. Here are a few things you need to know about when picking one.

Why People Prefer Digital Caliper.
Here are some of the top reasons for considering a digital caliper. Depending on the size of your requirement you can get a caliper for about $49-100. A battery is used to power the device. It lasts and so you do not have to worry about replacing the battery.

Woodworking Made Less Difficult With Grizzly Equipments
Woodworking is a craft that requires adequate skill and creativity. The skill of a woodworker is translated to the wood with the use of appropriate wood carving tools. One brand that is popular among Northern Tools customers is Grizzly Woodworking tools.

Talking About The Kreg Jig Pocket Hole Unit
Ask any woodwork enthusiasts what is the most popular and familiar of tools to them and invariably the response will be the pocket hole jig. This is of course that tool which allows wood to be joined together through the pocket hole joints it makes.

Kreg Jig Undertakings - Why You Ought To Buy A Pocket Hole Jig
If you love working with wood, then you have probably created your fair share of cabinets, cupboards, and other similar kinds of projects. Not only is it very enjoyable, it is also very therapeutic.

Information With Regards To The Intricacies Of Wood Carving
There are hobbies that are just suitable for a particular age or gender of a person, there are also hobbies that are forgotten as time passes by and there are some who remains despite all the new advancements in technologies and the innovation of the internet.